View AOZ6115_7190965.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

rev. 2.2 february 2010 www.aosmd.com page 1 of 11 AOZ6115 high performance, low r on , spst analog switch general description the AOZ6115 is a high performance single-pole single-throw (spst), low power, ttl-compatible bus switch. the AOZ6115 can handle analog and digital signals. signals with voltages up to v cc (1.65v to 5.5v) can be transmitted in ei ther direction. when the select pin is high, a is connected to the output b pin. the path that is open will have a high-impedance state with respect to the output. features sot23 and sc70 5-lead package 1.65v to 5.5v v cc operation low c on : 18pf applications audio and video signal routing battery operated equipment communications circuit relay replacement power routing typical application ic power supply + ? AOZ6115
AOZ6115 rev. 2.2 february 2010 www.aosmd.com page 2 of 11 ordering information aos green products use reduced levels of halogens, and are also rohs compliant. please visit www.aosmd.com/web/quality/rohs_compliant.jsp for additional information. pin configuration truth table part number ambient temperature range package environmental AOZ6115ci AOZ6115hi -40c to +85c sot23 5-lead sc70 5-lead rohs compliant green product 1 2 3 b a gnd 5 4 v cc s sot23-5l/sc70-5l (top view) logic s input function 0 no connection 1 a connected to b
AOZ6115 rev. 2.2 february 2010 www.aosmd.com page 3 of 11 absolute maximum ratings exceeding the absolute maximum ratings may damage the device. recommend operating ratings the device is not guaranteed to operate beyond the maximum operating ratings. notes: 1. the input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. 2. negative current should not exceed minimum negative value. 3. all leads welded or soldered to pc board. 4. unused inputs must be held high or low. they may not float. symbol parameter rating v cc supply voltage -0.5v to +6v v sw switch voltage (1) -0.5v to v cc v in input voltage (1) -0.5v to v cc i ik minimum input diode current (2) -50ma i sw switch current 130ma i swpeak peak switch current (pulsed at 1ms, <10% duty cycle) 260ma t stg storage temperature range -65c to +150c t j maximum junction temperature +150c p d sot23-5 power dissipation at 85c (3) 300mw esd human body model (jesd22a-114e) 8000v symbol parameter rating v cc supply voltage 1.65v to +5.5v v in control input voltage (4) 0v to v cc v sw switch input voltage 0v to v cc t a operating temperature -40c to +85c
AOZ6115 rev. 2.2 february 2010 www.aosmd.com page 4 of 11 electrical characteristics (continued) unless otherwise indicated, spec ifications indicate a temper ature range of -40c to +85c note: 1. typical values: symbol parameter test conditions min. typ. (1) max. units dc characteristics v ih input voltage high v cc = 2.7v to 3.6v 1.5 v v cc = 4.5v to 5.5v 2.0 v il input voltage low v cc = 2.7v to 3.6v 0.6 v v cc = 4.5v to 5.5v 0.8 r on on resistance v cc = 2.7v, i out = 100ma, b = 1.5v 3.0 4.0 ? v cc = 4.5v, i out = 100ma, b = 3.5v 2.0 3.0 r flat on resistance flatness v cc = 4.5v, i out = 100ma, b = 0v, 1v, 2v 0.8 ? i in input leakage current v in = 0v or v cc -1.0 1.0 a i b(off) off stage switch leakage v cc = 5.5v, a = 1v, 4.5v, b = 4.5v, 1v -100 4 100 na i a(on) on state switch leakage v cc = 5.5v, a = 1v, 4.5v, b = floating -20 1 20 na power supply v cc power supply range 1.65 5.5 v i ccq quiescent supply current v cc = 5.5v, v in = 0v or v cc , i out = 0v 0.5 1 a i cct increase in i cc per input v cc = 3.6v, v in = 2.0v 3.3 10 a v cc = 5.5v, v in = 2.4v 20 30 ac characteristics t on turn-on time b = 1.5v, r l = 50 ? , c l = 35pf v cc = 2.7v to 3.6v 20 65 ns v cc = 4.5v to 5.5v 10 40 t off turn-off time b = 1.5v, r l = 50 ? , c l = 35pf v cc = 2.7v to 3.6v 20 30 ns v cc = 4.5v to 5.5v 10 20 q charge injection c l = 1.0nf, v ge = 0v, r gen = 0 ? v cc = 2.7v to 3.6v 1 pc v cc = 4.5v to 5.5v 2 analog switch characteristics oirr off isolation r l = 50 ? , f = 1mhz -70 db bw -3db bandwidth r l = 50 ? 300 mhz thd total harmonic distortion v cc = 5v, r l = 600 ? , c l = 50pf, f = 20hz to 20khz 0.005 % capacitance c in control pin capacitance v cc = 0v, f = 1mhz 2 pf c off b port off capacitance v cc = 4.5v, f = 1mhz 7.5 pf c on a port capacitance when switch enable v cc = 4.5v, f = 1mhz 18 pf
AOZ6115 rev. 2.2 february 2010 www.aosmd.com page 5 of 11 ac loading and waveforms v out r l c l 35pf cl includes fixture and stray capacitance s v out r c l gnd gen a b v gen input control 50 figure 1. turn-on/turn-off timing figure 3. bandwidth figure 2. charge injection figure 4. harmonic distortion b a vcc 0.9 x v out 0.9 x v out vcc 0v control input switch output 0 t r t f = = 2.5ns t off t on v out logic input waveform are inverted for switches with opposite logic sense gnd vcc v out on on off off off off in in v out 50% q = ( v out )(c l ) 50 50 gnd vcc b n a s + network analyzer source signal 600 600 gnd b n a s + audio analyzer source signal vcc c l c l includes fixture and stray capacitance
AOZ6115 rev. 2.2 february 2010 www.aosmd.com page 6 of 11 ac loading and wavef orms (continued) figure 5. off isolation figure 6. on/off capacitance measurement capacitance meter f = 1mhz 10nf vcc s 0v or vcc gnd a b s b a gnd v out 50 50 50 vcc network analyzer vcc or 0v + source signal v in
AOZ6115 rev. 2.2 february 2010 www.aosmd.com page 7 of 11 package dimensions, sot23-5l gauge plane seating plane l2 e1 a2 aaa a1 0.95 1.90 unit: mm 0.80 0.63 2.40 a eb c l d ee1 5 1 notes: 1. package body sizes exclude mold flash and gate burrs. mold flash at the non-lead sides should be less than 5 mils. 2. dimension "l" is measured in gauge plane. 3. tolerance 0.10mm (4 mil) unless otherwise specified 4. refer to jedec mo-193c ab. 5. controlling dimension is millimeter, converted inch dimensions are not necessarily exact. symbols a a1 a2 b c d e e1 e e1 l l2 aaa dimensions in millimeters min. 0.00 0.70 0.35 0.10 2.80 2.60 1.50 0.30 0 nom. 0.88 0.40 0.13 2.90 2.80 1.60 0.95 bsc 1.90 bsc 0.40 0.25 bsc 0.10 max. 1.00 0.10 0.95 0.50 0.20 3.00 3.00 1.70 0.60 8 symbols a a1 a2 b c d e e1 e e1 l l2 aaa dimensions in inches min. 0.00 0.028 0.014 0.004 0.110 0.102 0.059 0.012 0 nom. 0.035 0.016 0.005 0.114 0.110 0.063 0.037 bsc 0.075 bsc 0.016 0.010 bsc 0.004 max. 0.039 0.004 0.037 0.020 0.008 0.118 0.118 0.067 0.024 8 recommended land pattern
AOZ6115 rev. 2.2 february 2010 www.aosmd.com page 8 of 11 tape and reel dimensions, sot23-5l tape reel leader/trailer and orientation trailer tape 300mm min. components tape orientation in pocket leader tape 500mm min. k0 b0 p0 a0 p1 p2 d0 d1 e1 e2 e unit: mm unit: mm j r feeding direction tape size 8mm reel size ?177.8 m ?177.8 max. n 55.0 min. w1 8.4 +1.50 / -0.0 package sot23-5/6l lp a0 3.15 0.10 b0 3.20 0.10 k0 1.40 0.10 d0 1.50 0.05 d1 1.00 +0.10 / -0 e 8.00 0.30 e1 1.75 0.10 e2 3.50 0.05 p0 4.00 0.10 p1 4.00 0.10 p2 2.00 0.05 t 0.23 0.03 h 13.0 +0.5 / -0.2 s 1.5 min k 10.1 min. r 12.7 j 4.0 0.1 w1 m n s k h
AOZ6115 rev. 2.2 february 2010 www.aosmd.com page 9 of 11 package dimensions, sc70-5l e1 d e1 e a a2 a1 b c l e l1 0.65 0.35 1.95 0.65 .010mm gauge plane notes: 1. all dimensions are in millimeters. 2. dimensions are inclusive of plating 3. package body sizes exclude mold flash and gate burrs. mold flash at the non-lead sides should be less than 3 mils each. 4. die is facing up for mold and facing down for trim/form; i.e., reverse trim/form. 5. dimension l is measured in gauge plane. 6. controlling dimension is millimeter, converted inch dimensions are not necessarily exact. symbols a a1 a2 b c d e e e1 e1 l l1 r 1 dimensions in millimeters min. 0.90 0.00 0.7 0.15 0.08 0.26 0.1 0 nom. 0.95 ? 0.9 0.22 0.127 2.10 bsc 2.30 bsc 0.65 bsc 1.30 bsc 1.30 bsc 0.40 2.54 bsc ? 4 7 nom max. 1.10 0.10 1.00 0.30 0.20 0.46 ? 8 symbols a a1 a2 b c d e e e1 e1 l l1 r 1 dimensions in inches min. 0.035 0.00 0.028 0.006 0.003 0.010 0.004 0 nom. 0.037 ? 0.035 0.008 0.005 0.083 bsc 0.091 bsc 0.026 bsc 0.051 bsc 0.051 bsc 0.015 0.01 bsc ? 4 7 nom max. 0.043 0.004 0.039 0.012 0.008 0.018 ? 8 recommended land pattern 0.975 r 1
AOZ6115 rev. 2.2 february 2010 www.aosmd.com page 10 of 11 tape and reel dimensions, sc70-5l carrier tape reel tape size 8mm reel size ?180 m ?180.00 0.50 package sc-70, 6l (8mm) a0 2.40 0.10 b0 2.40 0.10 k0 1.19 0.10 d0 1.00 min. d1 1.55 0.05 e 8.00 0.30 e1 1.75 0.10 e2 3.50 0.05 p0 4.00 0.10 p1 4.00 0.10 p2 2.00 0.05 t 0.25 0.05 n ?60.50 k0 unit: mm b0 g m w1 s k h n w v r trailer tape 300mm min. or 75 empty pockets components tape orientation in pocket leader tape 500mm min. or 125 empty pockets a0 p1 p2 feeding direction p0 e2 e1 e d0 t d1 w 9.00 0.30 w1 11.40 1.00 h ?13.00 +0.50/-0.20 k 10.60 s 2.00 0.50 g ?9.00 r 5.00 v 18.00 leader/trailer and orientation
AOZ6115 rev. 2.2 february 2010 www.aosmd.com page 11 of 11 as used herein: 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provid ed in the labeling, can be reasonably expected to result in a significant injury of the user. 2. a critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. this datasheet contains preliminary data; supplementary data may be published at a later date. alpha & omega semiconductor reserves the right to make changes at any time without notice. life support policy alpha & omega semiconductor products ar e not authorized for use as critical components in life supp ort devices or systems. part marking AOZ6115ci ar2d 11 week & year code part number code assembly location code assembly lot code AOZ6115hi week & year code part number code assembly location code assembly lot code c2d

▲Up To Search▲

Price & Availability of AOZ6115

	To Download AOZ6115 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .